A1011 HSLA Sheet possesses higher strength properties along with improved formability, weldability, and / or atmospheric corrosion resistance than normally obtained from conventional carbon sheet steels. These desirable properties are obtained through selected chemical composition and controlled mill processing. Alro Also Stocks:A1011 Type B A1011/A1011M Miami Valley SteelASTM A1011 is a hot rolled commercial quality steel produced from low carbon, rimmed, capped or semi-kilned steel. This steel is suitable for most processing techniques, and is generally used for bending and moderate forming. A1011 is also easy to fabricate and can often be found in drums, bins, barrels, lockers, cabinets, blower and ventilating systems, chutes, doors, and even automotive and agricultural
ASTM A568, A1011, A635, A1018, A659, A749, SAE J1392, SAE J2340, Information provided by AK Steel AK Steel ASTM A 1011, Grade 50 Hot Rolled Carbon Steel, Structural Steel (SS) Advanced Composition Property Material Type Manufacturer Trade Name UNS Number ASTM A1011 / A1011M - 18a Standard Specification for Steel 2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ASTM Standards. A370 Test Methods and Definitions for Mechanical Testing of Steel Products. A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for ASTM A1011 HSLAS F Grade 50 ASTM A1011 A1011M STEEL HSLA Grade 50 steel,HSLA Grade 50 Steel Mechanical HSLA Grade 50 is a material grade and designation defined in ASTM A572 standard.ASTM A572 is an international material standard for billet steel for general structural usage.A-36 steel can be compared with this type of steel.HSLA Grade 50 Steel Chemical Composition ASTM A572 defines the
A588/A588M Specification for High-Strength Low-Alloy Structural STeel, up to 50 ksi [245 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance; ASTM A572 Grade 50, 60 & 65 Data Sheet Properties. Chemical properties shall conform to the requirements prescribed COLD ROLLED - AK SteelTight control over chemical composition, hot rolling parameters, amount of cold reduction, annealing time and temperature, and the amount of temper High Strength Low Alloy Steel (HSLAS) Grade 40/SAE J1392 040 YLK 40 280 55 380 25 Grade 45 CL 2/ SAE J1392 045 XLK 45 310 55 380 22 Grade 50 CL 1/ SAE J1392 050 YLK 50 340 65 450 20 Grade 50 Carbon & High Strength Low Alloy (HSLA) Structural Steel Leeco ® Steel carries a deep inventory of carbon - or mild - steel plate as well as High Strength Low Alloy - or HSLA - steel plate. HSLA boasts a higher strength, lower weight and good machinability and ductility compared to conventional mild carbon steel grades. HSLA structural steels are manufactured to meet specific mechanical properties, such as hardness, strength, corrosion resistance
40 ksi). The chemical composition of a specific HSLA steel may vary for different product thicknesses to meet mechanical property requirements. The HSLA steels in sheet or plate form have low carbon content (0.05 to 0.25% C) in order to produce adequate formability and weldability, and they have manganese content up to 2.0%. PRODUCT GUIDES - Central SteelHSLA ASTM A 572 Gr 50 3/16 - 2-1/2 50 65 90° 2 t transverse About the same corrosion resistance as CQ ASTM A 588 Gr 50 aka Cor-Ten* 3/16 ASTM A 1011 CS Type B .071 - .171 x 36 - 72 Temper rolled, .10% max carbon, cold reduced Cold reduced sheet/plate is: Standard Specication for Steel, Sheet and Strip, Hot Designation:A 1011/A 1011M 07 Standard Specication for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength1 This standard is issued under the xed designation A 1011/A 1011M; the number immediately following the designation
Ryersons steel sheet comes in a variety of grades and thicknesses. We offer carbon sheet coated, cold rolled, hot rolled, painted and as expanded metal. Common applications range from construction framing and ductwork to machinery framing. Available grades include CS B, FS B, DS-B, DDS, EDDS, A36, A572-50, SS Grades 30-55 HSLA Grades 40-80 HSLA Grade 50 steel,HSLA Grade 50 Steel Mechanical HSLA Grade 50 Steel Chemical Composition :ASTM A572 defines the chemical composition of HSLA Grade 50 steels as under:Maximum percentage of Carbon (C) is 0.230. Maximum percentage of Manganese (Mn) is 1.35. Maximum percentage of Phosphorous (P) is 0.040. Maximum percentage of Sulphur (S) is 0.050.